RTL8366S – SINGLE-CHIP 5+1-PORT 10/100/1000 MBPS SWITCH CONTROLLER

Part Number : RTL8366S

Function : SINGLE-CHIP 5+1-PORT 10/100/1000 MBPS SWITCH CONTROLLER

Manufactures : Realtek

Images :

1 page
RTL8366S image

2 page
pinout

Description :

RTL8366S/SR SINGLE-CHIP 5+1-PORT 10/100/1000 MBPS SWITCH CONTROLLER WITH DUAL MAC INTERFACES DATASHEET Rev. Pre-1.4 19 Oct. 2007 Track ID: Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com.tw RTL8366S/SR DATASHEET COPYRIGHT ©2007 Realtek Semiconductor Corp. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of Realtek Semiconductor Corp. DISCLAIMER Realtek provides this document “as is”, without warranty of any kind, neither expressed nor implied, including, but not limited to, the particular purpose. Realtek may make improvements and/or changes in this document or in the product described in this document at any time. This document could include technical inaccuracies or typographical errors. TRADEMARKS Realtek is a trademark of Realtek Semiconductor Corporation. Other names mentioned in this document are trademarks/registered trademarks of their respective owners. USING THIS DOCUMENT This document is intended for the hardware and software engineer’s general information on the Realtek RTL8366S/SR chips. Though every effort has been made to ensure that this document is current and accurate, more information may have become available subsequent to the production of this guide. In that event, please contact your Realtek representative for additional information that may help in the development process. REVISION HISTORY Revision Pre-1.0 Pre-1.1 Pre-1.2 Release Date 2007/03/30 2007/04/16 2007/05/11 Summary Preliminary release. Enhance function description and correct some features typo. Remove pins strapping function in LED_P4_2, LED_P3_2, LED_P3_0, LED_P2_2, LED_P0_2, LED_P1_0, and LED_P0_0. Change pins name of STESTG0/1/2, STESTL0/1/2, STESTT, STESTH, STESTCKP/N, STESTOP/N, and STESTIP/N to SGND, SVDDL, SVDDT, SVDDH, SDCKP/N, SDTXP/N, and SDRXP/N. Figure 8, Figure 9, Table 2, Table 3, Table 5, and Table 16. Add Serdes interface pin description and mode selection in section 6.2 and 9.4. Add LED_P4_2/RESERVED pin description for normal operation. Add configuration strapping pins description in section 6.6. Remove chapter 3 and enhance application example in chapter 4. Add 1000Base-X application example circuit in Figure 25. Enhance General Purpose Interface description in section 9.3. Revise Figure 3, Block Diagram of RTL8366S/SR. Revise Applications Block Diagram, Figure 4, Figure 5, Figure 6, and Figure 7. ii Track ID: Rev. Pre-1.4 6-port 10/100/1000Mbps Single Chip Switch Controller RTL8366S/SR DATASHEET Pre-1.3 2007/08/03 Change the LED_P4_0/DisBlink description in section 8.20. Use pin floating to disable and pull down to enable power on blinking function. Remove the original section 8.12.4. Change the description in section 8.12.4, which only insert PVID for untagged […]

3 page
image

RTL8366S Datasheet


This entry was posted in Uncategorized. Bookmark the permalink.