TZA3001BHL Datasheet PDF – Integrated Laser Driver

Part Number : TZA3001BHL

Function : SDH/SONET STM4/OC12 Laser Driver

Package : LQFP32 Type

Manufacturers : Philips Electronics

Pinouts :

TZA3001BHL datasheet

 

Description :

The TZA3001AHL, TZA3001BHL and TZA3001U are fully integrated laser drivers for STM4/OC12 (622 Mbits/s) systems, incorporating the RF path between the data multiplexer and the laser diode. Since the dual loop bias and modulation control circuits are integrated on the IC, the external component count is low. Only decoupling capacitors and adjustment resistors are required.

The TZA3001AHL features an alarm function for signalling extreme bias current conditions. The alarm low and high threshold levels can be adjusted to suit the application using only a resistor or a current Digital-to-Analog Converter (DAC).

Features

1. RF output current sinking capability of 60 mA
2. Bias current sinking capability of 90 mA
3. Power dissipation of 430 mW (typical value)
4. Low cost LQFP32 plastic package
5. Single 5 V power supply.
6. Automatic laser shutdown
7. Few external components required

Other data sheets within the file : TZA3001AHL, TZA3001BHL, TZA3001U

TZA3001BHL Datasheet PDF Download


TZA3001BHL pdf

 

LD-450-1600MG PDF – Blue Laser Diode

Part Number : LD-450-1600MG

Function : Blue Laser Diode

Manufactures : Roithner LaserTechnik

Images :

1 page
LD-450-1600MG image

2 page
pinout

Description :

LD-450-1600MG v 1.0 24.07.2014 Description LD-450-1600MG is a blue multi transverse mode laser diode emitting at typically 450nm with rated output power of 1600 mW CW, in a standard 5.6 mm TO package. Maximum Ratings Parameter Operating Current Reverse Current Operating Temperature Storage Temperature Soldering Temperature Junction Temperature Symbol IF IR TCASE TSTG TSOLDER TJ Values Min. + 10 – 40 Max. 1.6 20 + 70 + 85 260 150 Unit A mA °C °C °C °C Laser Characteristics (TCASE = 25°C, IF = 1.2 A) Parameter Emission Wavelength Optical output power Treshold Current Operating Current Operating Voltage Beam Divergence (FWHM) Polarization Thermal resitance Symbol λpeak PO Ith IF VF ӨII x Ө┴ PGR Rth Min. 440 1.3 – x 19 Values Typ. 450 1.6 0.2 1.2 4.8 7 x 23 100:1 15 Max. 460 0.3 1.5 6.0 – x 27 Unit nm W A A V deg K/W www.roithner-laser.com 1 Performance Characteristics Optical Output Power Operating Voltage Threshold Current Spectrum www.roithner-laser.com 2 Drawing All dimensions in mm Electrical Connection Lead Pin 1 Pin 2 Pin 3 Description LD anode Case LD cathode www.roithner-laser.com 3 ESD Caution Always do handle laser diodes with extreme caution to prevent electrostatic discharge, the primary cause of unexpected diode failure. ESD failures can be prevented by always wearing wrist straps, only using a grounding workplace, and following strict anti-static guidelines when handling the laser diode Safety Advice This laser diode emits highly concentrated blue light which can be hazardous to the human eye and skin. This diode is classified as CLASS 4 laser product according to IEC 60825-1 and 21 CFR Part 1040.10 Safety Standards. Operating Considerations Operating the laser diode outside of its maximum ratings may cause failure or a safety hazard. The diode may be damaged by excessive drive currents or switching transients. If the diode is operated using a power supply, it is strongly recommended to connect the diode with the output voltage set to zero. The voltage should then be increased slowly and with great caution, while at the same time carefully monitoring the laser diodes output power and drive current. The laser diode will show accelerated degradation with increased temperature, and it is advised to keep the case temperature low therefor, by means of heat sinking the device. © All Rights Reserved The above specifications are for reference purpose only and subjected to change without prior notice www.roithner-laser.com 4 […]

3 page
image

LD-450-1600MG Datasheet