ATMEGA328A PDF Datasheet – 8-Bit Microcontroller

This post explains for the Microcontroller. The ATmega328A is a microcontroller chip manufactured by Microchip Technology, formerly Atmel Corporation. It is part of the AVR microcontroller family and is widely used in various embedded systems and DIY electronics projects. The ATmega328A is an improved version of the earlier ATmega328 microcontroller and is commonly found on the Arduino Uno development board.

The Part Number is ATMEGA328A.

The function of this semiconductor is 8-bit Microcontroller.

The package is DIP 28 Pin, TQFP 32 Pin Type

Manufacturer: Atmel

Preview images :

1 page
ATMEGA328A pdf atmel

Description

The ATMEGA328, ATMEGA328A is a low-power CMOS 8-bit microcontroller based on the AVR
enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the
ATmega48A/PA/88A/PA/168A/PA/328/P achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.

The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers.

Features

1. High Performance, Low Power Atmel AVR 8-Bit Microcontroller Family

2. Advanced RISC Architecture

(1) 131 Powerful Instructions – Most Single Clock Cycle Execution

(2) 32 x 8 General Purpose Working Registers

(3) Fully Static Operation

(4) Up to 20 MIPS Throughput at 20MHz

(5) On-chip 2-cycle Multiplier

3. Peripheral Features

(1) Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode

(2) One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode

Pinouts

ATMEGA328A pinout datasheet

ATMEGA328A Datasheet PDF

MX1515 PDF Datasheet – Brush DC Motor Driver

Part Number: MX1515

Function: Brush DC motor driver

Package: DIP 16 Pin Type

Manufacturer: Sinotech Mixic Electronics

Images:MX1515 datasheet

Description

This product provides an integrated brushed DC motor drive solution for battery powered toys, low voltage or battery powered motion control applications. The circuit integrates a two-channel H-bridge drive circuit designed with N-channel and P-channel power MOSFETs, which is suitable for driving electric toy cars steering wheel and rear-wheel drive. The circuit has a wide operating voltage range (from 2V to 9.6V), the maximum continuous output current of steering wheel drive reaches 1.5A, the maximum peak output current reaches 2.5A, the maximum continuous output current of rear wheel drive reaches 1.5A, and the maximum peak output current reaches 1.5A. The current reaches 2.5A. The drive circuit has a built-in overheat protection circuit. When the load current through the drive circuit is much larger than the maximum continuous current of the circuit, the junction temperature of the chip inside the circuit will rise rapidly due to the limitation of the heat dissipation capacity of the package. Once the set value (typical value of 150°C) is exceeded, the internal circuit will immediately shut down. Cut off the output power tube, cut off the load current, and avoid the safety hazards such as smoke and fire caused by the plastic package caused by the continuous increase of temperature. The built-in temperature hysteresis circuit ensures that the circuit can be controlled again only after the circuit returns to a safe temperature. […]

MX1515 pdf pinout

Features:

1. Low standby current (less than 0.1uA)

2. Low quiescent working current

3. Integrated H-bridge drive circuit

4. Built-in anti-common state conduction circuit

5. Power MOSFET tube with low conduction internal resistance

6. Built-in thermal protection circuit (TSD) with hysteresis effect

7. Antistatic level: 3KV (HBM).

MX1515 PDF Datasheet