memory

24LC014 Datasheet PDF – 1K I2C Serial EEPROM – Microchip

Posted on by pinout

Part Number: 24LC014

Function : 1K I2C Serial EEPROM

Package: 8-Lead PDIP, SOIC, TSSOP, DFN, TDFN and MSOP Packages, 6-Lead SOT-23

Manufacturer: Microchip

Image

24LC014 image

Description

The Microchip Technology Inc. 24AA014, 24LC014 is a 1 Kbit Serial Electrically Erasable PROM with operation down to 1.7V. The device is organized as a single block of 128 x 8-bit memory with a 2-wire serial interface. Low-current design permits operation with typical standby and active currents of only 1 A and 1 mA, respectively. The device has a page write capability for up to 16 bytes of data. Functional address lines allow the connection of up to eight 24AA014 / 24LC014 devices on the same bus for up to 8 Kbits of contiguous EEPROM memory.

Pinout

24LC014 datasheet

Features

1. Single-Supply with Operation down to 1.7V

2. Low-Power CMOS Technology :

(1) 1 mA active current, typical

(2) 1 μA standby current, typical at 5.5V

3. Organized as a Single Block of 128 Bytes (128 x 8)

4. Hardware Write Protection for Entire Array

5. 2-Wire Serial Interface Bus, I2C™ Compatible

6. 100 kHz and 400 kHz Clock Compatibility

7. Page Write Buffer for up to 16 Bytes

8. Self-Timed Write Cycle (including auto-erase)

Other data sheets are available within the file: 24AAO14, 24LCO14

24LC014 Datasheet PDF


 

Related articles across the web

25L8005 Datasheet PDF – 8M Bit CMOS Serial Flash Memory

Posted on by pinout

Part Number: 25L8005

Function : 8M Bit CMOS Serial Flash Memory

Package:

– 8-pin SOP (150mil)
– 8-pin SOP (200mil)
– 8-pin PDIP (300mil)
– 8-land SON/WSON (6x5mm), 8-land SON is not recommended for new design
– 8-land USON (4x4mm)

Manufacturer: Macronix ( http://www.macronix.com )

Image

25L8005 image

Description

The MX25L8005 is a CMOS 8,388,608 bit serial Flash memory, which is configured as 1,048,576 x 8 internally. The 25L8005 feature a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The three bus signals are a clock input (SCLK), a serial data input (SI), and a serial data output (SO). Serial access to the device is enabled by CS# input.

The 25L8005 is designed to offer protection against accidental erasure or programming caused by spurious system level signals that may exist during power transition. During power up the device automatically resets the state machine in the standby mode. In addition, with its control register architecture, alteration of the memory contents only occurs after successful completion of specific command sequences. The device also incorporates several features to prevent inadvertent write cycles resulting from VCC power-up and power-down transition or system noise.

 

Pinout

25L8005 datasheet

Features

1. Serial Peripheral Interface compatible — Mode 0 and Mode 3

2. 8,388,608 x 1 bit structure

3. 256 Equal Sectors with 4K byte each
(1) Any Sector can be erased individually

4. 16 Equal Blocks with 64K byte each
(1) Any Block can be erased individually

5. Single Power Supply Operation
(1) 2.7 to 3.6 volt for read, erase, and program operations

6. Latch-up protected to 100mA from -1V to Vcc +1V

25L8005 Datasheet PDF

25L8005 pdf